How to adjust Winchester Model 70 trigger?

The Winchester Model 70 trigger can be adjusted by anyone familiar with basic firearm maintenance. However, it is recommended that you take your firearm to a qualified gunsmith if you are unsure of how to perform the adjustment correctly.

To adjust the trigger, you will need:

1. Remove the stock from the receiver.
2. Once the stock is removed, locate the two set screws on the outside of the trigger housing. Loosen these screws until they are flush with the housing, but do not remove them completely.
3. Next, locate the tension screw inside the trigger housing. This screw controls how much pressure must be applied to the trigger for it to release the sear and fire.
4. By turning this screw clockwise, you will increase the amount of pressure needed to fire the gun. Conversely, turning the screw counterclockwise will decrease the amount of pressure needed. It is important to note that you should make small adjustments to this screw, as too much pressure can make the trigger dangerous to use.
5. Once you have finished adjusting the trigger, be sure to test it with an unloaded gun to make sure that it is working properly.
6. Finally, remember to re-tighten the set screws before returning the stock to the receiver.

Video for a visual example:

There are a few things you can do to adjust the trigger on your Winchester Model 70.

First, take a look at the trigger assembly and make sure that all of the parts are tight and in good working condition. If anything looks damaged or out of place, it may need to be replaced.Trigger pull is adjusted by turning the screw labeled “Trigger Pull.” Turning it clockwise will increase trigger pull weight, and counter-clockwise will reduce it. The screw is factory set for three pounds (3lbs). DO NOT exceed five pounds (5lbs). Doing so could cause damage to your gun.

If the sear needs adjustment, carefully file down the engagement surface on either side of the sear until it releases consistently at the desired weight. Be careful not to over-file, as this could damage the sear and make the gun unsafe to fire.

You may also want to try a different type of ammunition in your Winchester Model 70. Different brands and types of ammo can have different effects on trigger pull. If you’re having trouble with light primer strikes or misfires, switching to a harder primer may help. You can also try using a heavier bullet weight. This will usually create more resistance in the trigger, which can help with light primer strikes.

If you’re still having trouble after trying all of these things, you may need to take your gun to a qualified gunsmith for further diagnosis and repair.

The Winchester Model 70 is a bolt-action sporting rifle. It has a Monte Carlo stock, a poured aluminum receiver, and a cold hammer-forged barrel. It is widely used for hunting game animals such as deer and elk.

The trigger of the Winchester Model 70 can be adjusted to your preference with just a few minutes of work. You will need a small screwdriver or Allen wrench to make the adjustment.

First, remove the stock from the gun by unscrewing the screws that hold it in place. Be careful not to lose any of the small parts or springs that may come out with the stock. Next, locate the trigger adjustment screw on the outside of the trigger housing (it will have an “R” or “L” stamped next to it).

If the trigger is too light, turn the adjustment screw to the right (clockwise) until the desired weight is achieved. If the trigger is too heavy, turn the adjustment screw to the left (counter-clockwise) until the desired weight is achieved. Once the correct setting is found, replace the stock and screws. Test the trigger by dry firing the gun a few times before loading it.

There are a few things you can do to adjust the trigger on your Winchester Model 70.

First, you can try adjusting the screw that holds the trigger in place. This screw is located just above the trigger guard, and turning it clockwise will make the trigger lighter, while turning it counterclockwise will make it heavier.

If this doesn’t have the desired effect, or if the screw won’t budge, then you may need to take your gun to a qualified gunsmith for further adjustment.

Alternatively, you can purchase an aftermarket trigger kit that will give you more control over the trigger pull weight.

Whichever route you choose, be sure to follow all safety precautions when working with firearms!

There are a few things that you can do to adjust the trigger on your Winchester Model 70 rifle.

First, you will need to remove the stock from the rifle. Next, locate the screw that adjusts the trigger pull weight. This screw is located just above the trigger guard, on the left side of the receiver.

Turning this screw clockwise will increase the trigger pull weight, while turning it counterclockwise will decrease the trigger pull weight.

Once you have adjusted the trigger pull weight to your liking, reassemble the rifle and test it out.

If you find that yourtrigger is still not functioning properly, or if you are experiencing any other issues with your rifle, be sure to take it to a qualified gunsmith for further assistance.

For triggers installed after 2005, there is an adjustment screw located behind the trigger. This screw dictates how much travel there is before thetrigger breaks. For example, if you turn the screw all the way in, it will create a zero travel or “hair” trigger. If you back this screw out, it will increase travel and make the trigger heavier. Please be aware that if you decrease travel too much, it could create an unsafe condition where the gun might fire without you meaning for it to do so.

If your Model 70 was manufactured before 2005, then your rifle’s trigger is not adjustable.